白小姐中特网必选一肖

Times [Font: large, medium and small ]

What are the requirements for the installation process of FRP desulfurization tower

Pay attention to ensure the diameter of the tower body after assembly, especially the diameter error of the tower air outlet on the glass fiber reinforced plastic desulfurization tower should be as small as possible. When the tower body is assembled and assembled, the glass fiber reinforced plastic desulfurization tower should pay attention to the circular arc surface of the gasket and the arc surface of the base of the tower ribs. The assembly of the lower shell should ensure that the watertight power supply has safety measures. After the power cord is connected, remember The junction box should be sealed to prevent moisture from entering and burning out.

The direction of the water inlet and outlet pipes can be adjusted by changing the direction of the screw holes on the flange according to the actual situation on site. The fan should be installed to draw upward air, the gap between the fan blade end and the tower body should be uniform not more than 100mm, 4 blades should be adjusted at the same angle, and the rotation plane of the impeller should be perpendicular to the center line. It is required that the installation surface of the water-filling filler layer be flat and uniformly spaced.

Ensure that the lower column and the lower inlet pipe are in good contact with the foundation. The foundation installation surface of the foundation steel plate and the glass fiber reinforced plastic desulfurization tower is cut flat and ensure that the axis of the lower column and the lower inlet pipe is perpendicular to the foundation surface on the same water surface. Circulating water pump is used for FRP desulfurization tower. Pay attention to its flow rate and the amount of cooling water. When using FRP desulfurization tower, the cooling tower should be kept within ± 5% of the designed volume to prevent the water from being too large, which affects the cooling effect.

What are the requirements for the installation process of FRP desulfurization tower

1. Attention should be paid to the diameter of the glass fiber reinforced plastic desulfurization tower after the block assembly, especially the diameter error of the air outlet of the glass fiber reinforced plastic desulfurization tower should be as small as possible.

2. When the glass fiber reinforced plastic desulfurization tower body is assembled and assembled in blocks, the glass fiber reinforced plastic desulfurization tower should pay attention to making the circular arc surface of the gasket fit with the circular arc surface of the rib of the tower body, and the lower shell assembly should ensure watertightness.

3. There should be safety measures for the power supply of the FRP desulfurization tower. After the power cord is connected, remember that the junction box should be sealed to prevent moisture from entering and burning out.

4. The direction of the water inlet and outlet pipes of the FRP desulfurization tower can be adjusted by changing the direction of the screw holes on the flange according to the actual situation on site.

5. The FRP desulfurization tower fan should be installed to draw upward air, the gap between the fan blade end and the tower body should be uniform not more than 100mm, 4 blades should be adjusted at the same angle, and the rotation plane of the impeller should be perpendicular to the center line.

6. The glass fiber reinforced plastic desulfurization tower requires the installation surface of the water-filling filler layer to be flat and evenly spaced.

7. The glass fiber reinforced plastic desulfurization tower ensures that the lower column and the lower water inlet pipe are in good contact with the foundation. The foundation embedded steel plate and the glass fiber reinforced plastic desulfurization tower base installation surface are leveled and ensured that the axis of the lower column and the lower water inlet pipe is perpendicular to the foundation surface.

8. Circulating water pump is used for FRP desulfurization tower. Pay attention to its flow rate and the amount of cooling water. When using FRP desulfurization tower, the cooling tower should be kept within ± 5% of the design volume, so that the water resistance is too large, which affects the cooling effect.


NEXT: FRP purification tower anti-corrosion
NEXT: To what extent is the resistance of FRP storage tanks to high temperature and pressure in the application?
Copyright © 2015 Hebei Yiyang Antai Environmental Protection Equipment Co., Ltd. - FRP pickling tank | FRP purification tower | FRP desulfurization tower | FRP mixing tank All rights reserved.
Address: Chengnan Development Zone, Huanghua City, Hebei Province Telephone: 0317-5628177 Mobile: 15233270999
Fax: 0317-5625066 Website: http://cafethera.com Technical Support: Cangzhou Xianyue Network QQ79471598